Festplatte Defekt?

[lisanisu]

Meine gute 1,5 TB Festplatte hat die Grätsche gemacht...

Smartmontools sagt einen Fehler bei der Laufzeit der Festplatte.
[code]Error 3791 occurred at disk power-on lifetime: 44774 hours (1865 days + 14 hours)[/code]

Kann man den Wert irgendwie wieder zurück setzen oder was anderes machen, damit ich mir keine neue Kaufen muss?
Festplatten sind echt mal Teuer...

[code]smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST31500341AS
Serial Number: 9VS38VTT
LU WWN Device Id: 5 000c50 01a5a5c75
Firmware Version: CC1H
User Capacity: 1,500,301,910,016 bytes [1.50 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Sep 2 20:45:25 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 617) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 296) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 098 082 006 Pre-fail Always - 51009135
3 Spin_Up_Time 0x0003 098 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 65
5 Reallocated_Sector_Ct 0x0033 001 001 036 Pre-fail Always FAILING_NOW 4092
7 Seek_Error_Rate 0x000f 066 060 030 Pre-fail Always - 141856511289
9 Power_On_Hours 0x0032 049 049 000 Old_age Always - 44774
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 60
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 4018
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 4295032833
189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 376
190 Airflow_Temperature_Cel 0x0022 071 046 045 Old_age Always - 29 (Min/Max 29/31)
194 Temperature_Celsius 0x0022 029 054 000 Old_age Always - 29 (243 52 0 0 0)
195 Hardware_ECC_Recovered 0x001a 047 017 000 Old_age Always - 51009135
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 44729 (150 180 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1552197965
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1925744148

SMART Error Log Version: 1
ATA Error Count: 3791 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 3791 occurred at disk power-on lifetime: 44774 hours (1865 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e5 00 00 00 00 00 a0 00 00:00:33.841 CHECK POWER MODE
ef 03 46 00 00 00 a0 00 00:00:26.251 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 00:00:26.188 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 00:00:26.187 NOP [Abort queued commands]
25 00 01 00 08 00 e0 00 00:00:26.187 READ DMA EXT

Error 3790 occurred at disk power-on lifetime: 44774 hours (1865 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e5 00 00 00 00 00 a0 00 00:00:33.841 CHECK POWER MODE
ef 03 46 00 00 00 a0 00 00:00:26.251 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 00:00:26.188 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 00:00:26.187 NOP [Abort queued commands]
25 00 01 00 08 00 e0 00 00:00:26.187 READ DMA EXT

Error 3789 occurred at disk power-on lifetime: 44774 hours (1865 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 00:00:26.251 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 00:00:26.188 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 00:00:26.187 NOP [Abort queued commands]
25 00 01 00 08 00 e0 00 00:00:26.187 READ DMA EXT
ef 03 46 00 00 00 a0 00 00:00:26.043 SET FEATURES [Set transfer mode]

Error 3788 occurred at disk power-on lifetime: 44774 hours (1865 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 00:00:26.043 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 00:00:25.979 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 00:00:25.979 NOP [Abort queued commands]
25 00 01 80 08 00 e0 00 00:00:25.979 READ DMA EXT
ef 03 46 00 00 00 a0 00 00:00:25.826 SET FEATURES [Set transfer mode]

Error 3787 occurred at disk power-on lifetime: 44774 hours (1865 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 00:00:26.043 SET FEATURES [Set transfer mode]
ff 00 00 00 00 00 00 00 00:00:25.979 [VENDOR SPECIFIC]
00 00 00 00 00 00 00 04 00:00:25.979 NOP [Abort queued commands]
25 00 01 80 08 00 e0 00 00:00:25.979 READ DMA EXT
ef 03 46 00 00 00 a0 00 00:00:25.826 SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 27026 -
# 2 Short offline Completed without error 00% 26978 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.[/code]

[schwedenmann]

Hallo

Kann man den Wert irgendwie wieder zurück setzen

ja, zumindest kann man einge der werte manipulieren.


mfg
schwedenmann

[mludwig]

Die Platte gibt die Selbsteinschätzung ab, dass sie in Kürze defekt sein wird, und empfiehlt alle darauf befindlichen Daten zu sichern. Sofern nicht bereits geschehen, würde ich sofort ein Backup anlegen, damit man wieder beruhigt nach vorne sehen kann.

SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.

Das zurücksetzen irgendwelcher Zähler wird die Sache nicht wirklich besser machen. In wieweit diese Bewertung stimmt, kannst du ja nach erstellen des Backup in aller Ruhe abwarten und schonmal suchen wo du Ersatz herbekommst, wenn es soweit ist.

mludwig