Probleme Ipaq - Sarge

Debian auf Notebooks und speziellen Geräten wie eingebetteten Systemen, Routern, Set-Top-Boxen, ...
Antworten
Benutzeravatar
ralf
Beiträge: 738
Registriert: 06.09.2002 13:39:10
Wohnort: Weserbergland

Probleme Ipaq - Sarge

Beitrag von ralf » 09.02.2005 22:24:16

Guten Abend zusammen.
Ich habe ein Problem mit meienem Compaq IPAQ 3970.
Ich kann mit Sarge nich auf in zugreifen.
Habe das Programm RAKI dafür verwendet.
Der PDA hat Windows Pocket PC 2003 drauf.
Ich habe mal die DMESG beigefügt.
Mein Sarge hat den Kernel 2.6.8.
Danke ung Gruß
Ralf



buero2:~# dmesg
egistered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f78f0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x67db, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178002
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0002
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 B1
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 C1
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 C9
16 001 01 1 1 0 1 0 1 1 D1
17 000 00 1 0 0 0 0 0 0 00
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ169 -> 0:16
IRQ177 -> 0:17
IRQ185 -> 0:18
IRQ193 -> 0:19
IRQ201 -> 0:21
IRQ209 -> 0:22
.................................... done.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:11.3, from 5 to 9
PCI: Via IRQ fixup for 0000:00:11.2, from 5 to 9
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4316 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20268: IDE controller at PCI slot 0000:00:05.0
ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 169
PDC20268: chipset revision 2
PDC20268: ROM enabled at 0xdffe0000
PDC20268: 100% native mode on irq 169
ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:pio, hdh:pio
hde: WDC WD800BB-00DAA1, ATA DISK drive
hdf: WDC WD800AB-00CBA1, ATA DISK drive
Using anticipatory io scheduler
ide2 at 0xec00-0xec07,0xe802 on irq 169
hde: max request size: 1024KiB
hde: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host2/bus0/target0/lun0: p1 p2
hdf: max request size: 128KiB
hdf: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host2/bus0/target1/lun0: p1
hdg: PIONEER DVD RW DVR-106D, ATAPI CD/DVD-ROM drive
ide3 at 0xe400-0xe407,0xe002 on irq 169
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 34098H4, ATA DISK drive
hdb: Maxtor 6B200P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 >
hdb: max request size: 1024KiB
hdb: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63, UDMA(133)
/dev/ide/host0/bus0/target1/lun0: p1 < p5 p6 > p2 p3
hdc: HL-DT-STDVD-ROM GDR8161B, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST GCE-8320B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2731008k swap on /dev/hdb6. Priority:-1 extents:1
Adding 1028120k swap on /dev/hde1. Priority:-2 extents:1
EXT3 FS on hdb2, internal journal
hdg: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
hdd: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, DMA
SCSI subsystem initialized
Capability LSM initialized
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
FAT: Unrecognized mount option "rw/umask=002" or missing value
ReiserFS: hde2: warning: unknown mount option "rw/umask=002"
FAT: Unrecognized mount option "rw/umask=002" or missing value
FAT: Unrecognized mount option "rw/umask=002" or missing value
FAT: Unrecognized mount option "rw/umask=002" or missing value
irda_init()
NET: Registered protocol family 23
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 185
eth0: RealTek RTL8139 at 0xd400, 00:e0:7d:b2:48:78, IRQ 185
eth0: Identified 8139 chip type 'RTL-8139C'
cmpci: version $Revision: 6.82 $ time 23:45:28 Sep 13 2004
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 193
cmpci:
cmpci: found CM8738 adapter at io 0xd000 irq 193
cmpci: chip version = 037
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 Audio codec, id: ALG32 (ALC650)
via82cxxx: board #1 at 0xCC00, IRQ 209
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:11.2: irq 201, io base 0000c400
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 21 (level, low) -> IRQ 201
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#2)
uhci_hcd 0000:00:11.3: irq 201, io base 0000c800
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using address 2
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
usb 2-1: new full speed USB device using address 2
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for PocketPC PDA
drivers/usb/serial/ipaq.c: USB PocketPC PDA driver v0.5
ipaq 1-2:1.0: PocketPC PDA converter detected
ipaq: probe of 1-2:1.0 failed with error -5
usbcore: registered new driver ipaq
hisax_isac: ISAC-S/ISAC-SX ISDN driver v0.1.0
hisax_fcpcipnp: Fritz!Card PCI/PCIv2/PnP ISDN driver v0.0.1
HiSax: Card 1 Protocol EDSS1 Id=fcpcipnp0 (0)
HiSax: DSS1 Rev. 2.32.2.3
HiSax: 2 channels added
HiSax: MAX_WAITING_CALLS added
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 177
hisax_fcpcipnp: found adapter Fritz!Card PCI v2 at 0000:00:06.0
Linux video capture interface: v1.00
pwc Philips webcam module version 9.0.1 loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC
830/840.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 a
nd MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
pwc Logitech QuickCam Pro 3000 USB webcam detected.
pwc Registered as /dev/video0.
usbcore: registered new driver Philips webcam
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2002 Netfilter core team
usb 2-2: new full speed USB device using address 3
usbaudio: device 2 audiocontrol interface 1 has 1 input and 0 output AudioStream
ing interfaces
usbaudio: device 2 interface 2 altsetting 0 FORMAT_TYPE descriptor not found
usbaudio: valid input sample rate 44100
usbaudio: device 2 interface 2 altsetting 1: format 0x00000010 sratelo 44100 sra
tehi 44100 attributes 0x00
usbaudio: valid input sample rate 22050
usbaudio: device 2 interface 2 altsetting 2: format 0x00000010 sratelo 22050 sra
tehi 22050 attributes 0x00
usbaudio: valid input sample rate 11025
usbaudio: device 2 interface 2 altsetting 3: format 0x00000010 sratelo 11025 sra
tehi 11025 attributes 0x00
usbaudio: valid input sample rate 8000
usbaudio: device 2 interface 2 altsetting 4: format 0x00000010 sratelo 8000 srat
ehi 8000 attributes 0x00
usbaudio: registered dsp 14,35
usbaudio: constructing mixer for Terminal 3 type 0x0101
usbaudio: warning: found 1 of 0 logical channels.
usbaudio: assuming the channel found is the master channel (got a Philips camera
?). Should be fine.
usbaudio: registered mixer 14,32
usb_audio_parsecontrol: usb_audio_state at f6e97a20
usbcore: registered new driver audio
drivers/usb/class/audio.c: v1.0.0:USB Audio Class driver
usb 1-2: USB disconnect, address 2
usbcore: registered new driver snd-usb-audio
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Samsung Model: Mighty Drive Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 502784 512-byte hdwr sectors (257 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
usb 1-2: new full speed USB device using address 3
/dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
USB Mass Storage device found at 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ipaq 1-2:1.0: PocketPC PDA converter detected
usb 1-2: PocketPC PDA converter now attached to ttyUSB0
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
Real Time Clock Driver v1.12
input: PC Speaker
PPP BSD Compression module registered
PPP Deflate Compression module registered
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
parport0: Printer, Kyocera FS-3700+
inserting floppy driver for 2.6.8-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
input: PS2++ Logitech Wheel Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 128M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
Disabled Privacy Extensions on device c02c95a0(lo)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 17
lp0: using parport0 (interrupt-driven).
NET: Registered protocol family 5
eth0: no IPv6 routers present
buero2:~#
Workstation1: Ubuntu 11.04, AMD64 3200+
Server: Ubuntu 8.04 LTS // geplanter DEBIAN 6 Server !!!
Workstation2: AMD Athlon 1800+, Debian
Laptop: Lenovo R61i, Windows XP

Antworten