smartctl -a /dev/sdc :( smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.16.0-1-amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA300 Serial Number: 27A07BHAS LU WWN Device Id: 5 000039 fe6ce332c Firmware Version: MX6OABB0 User Capacity: 3.000.592.982.016 bytes [3,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 7 21:16:26 2018 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (21504) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 359) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 141 141 054 Pre-fail Offline - 66 3 Spin_Up_Time 0x0007 137 137 024 Pre-fail Always - 393 (Average 442) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 639 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 3418 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 636 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 666 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 666 194 Temperature_Celsius 0x0002 146 146 000 Old_age Always - 41 (Min/Max 15/57) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 0f d9 96 92 01 Error: ICRC, ABRT at LBA = 0x019296d9 = 26384089 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 40 90 a8 29 93 40 08 00:07:03.052 WRITE FPDMA QUEUED 61 40 88 68 24 93 40 08 00:07:03.051 WRITE FPDMA QUEUED 61 40 80 28 1f 93 40 08 00:07:03.048 WRITE FPDMA QUEUED 61 40 78 e8 19 93 40 08 00:07:03.048 WRITE FPDMA QUEUED 61 40 70 a8 14 93 40 08 00:07:03.048 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 3418 - # 2 Extended offline Completed without error 00% 3369 - # 3 Extended offline Completed without error 00% 3257 - # 4 Extended offline Completed without error 00% 3208 - # 5 Extended offline Completed without error 00% 3137 - # 6 Extended offline Completed without error 00% 2898 - # 7 Extended offline Completed without error 00% 2655 - # 8 Extended offline Completed without error 00% 2608 - # 9 Extended offline Completed without error 00% 2548 - #10 Extended offline Completed without error 00% 2408 - #11 Extended offline Completed without error 00% 2345 - #12 Extended offline Completed without error 00% 2324 - #13 Extended offline Completed without error 00% 2231 - #14 Extended offline Completed without error 00% 2207 - #15 Extended offline Completed without error 00% 2167 - #16 Extended offline Completed without error 00% 2149 - #17 Extended offline Interrupted (host reset) 30% 1862 - #18 Extended offline Completed without error 00% 1811 - #19 Extended offline Completed without error 00% 1496 - #20 Extended offline Completed without error 00% 1070 - #21 Extended offline Completed without error 00% 914 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.