smartctl-sdd
von halo44- SNIPPET_TEXT:
-
- smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-8-amd64] (local build)
- Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Toshiba 2.5" HDD MQ01ABF...
- Device Model: TOSHIBA MQ01ABF050
- Serial Number: X5BTC6EGT
- LU WWN Device Id: 5 000039 694102186
- Firmware Version: AM001U
- User Capacity: 500.107.862.016 bytes [500 GB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 2.5 inches
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ATA8-ACS (minor revision not indicated)
- SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
- Local Time is: Thu Sep 13 09:07:44 2018 CEST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART Status not supported: Incomplete response, ATA output registers missing
- SMART overall-health self-assessment test result: PASSED
- Warning: This result is based on an Attribute check.
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 120) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 118) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
- 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
- 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1997
- 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1405
- 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
- 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
- 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
- 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 220
- 10 Spin_Retry_Count 0x0033 128 100 030 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 799
- 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 4
- 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 270
- 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 2721
- 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 21 (Min/Max 14/47)
- 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
- 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
- 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
- 199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 3
- 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
- 222 Loaded_Hours 0x0032 100 100 000 Old_age Always - 85
- 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
- 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
- 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 187
- 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
- SMART Error Log Version: 1
- ATA Error Count: 3
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 3 occurred at disk power-on lifetime: 218 hours (9 days + 2 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 50 00 ff 43 44 40 at LBA = 0x004443ff = 4473855
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 35 ff a0 60 3d 44 40 00 00:00:38.851 WRITE DMA EXT
- aa aa aa aa aa aa aa ff 00:00:38.388 [RESERVED]
- 35 00 a0 60 3d 44 40 00 00:00:38.154 WRITE DMA EXT
- 35 00 a0 c0 35 44 40 00 00:00:38.143 WRITE DMA EXT
- 35 00 d8 e8 2e 44 40 00 00:00:38.073 WRITE DMA EXT
- Error 2 occurred at disk power-on lifetime: 208 hours (8 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 51 00 7f 7f a5 40 Error: ICRC, ABRT at LBA = 0x00a57f7f = 10846079
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 35 00 f0 90 7e a5 40 00 00:29:19.997 WRITE DMA EXT
- 35 00 f0 a0 7d a5 40 00 00:29:19.882 WRITE DMA EXT
- 35 00 f0 b0 7c a5 40 00 00:29:19.767 WRITE DMA EXT
- 35 00 f0 c0 7b a5 40 00 00:29:19.652 WRITE DMA EXT
- 35 00 f0 d0 7a a5 40 00 00:29:19.537 WRITE DMA EXT
- Error 1 occurred at disk power-on lifetime: 183 hours (7 days + 15 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 50 00 f7 48 ac 40 at LBA = 0x00ac48f7 = 11290871
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 35 00 f0 08 48 ac 40 00 00:48:16.551 WRITE DMA EXT
- 35 00 f0 e0 71 c5 40 00 00:48:16.436 WRITE DMA EXT
- 35 00 f0 f0 70 c5 40 00 00:48:16.321 WRITE DMA EXT
- 35 00 f0 00 70 c5 40 00 00:48:16.206 WRITE DMA EXT
- 35 00 80 80 6f c5 40 00 00:48:16.142 WRITE DMA EXT
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Quellcode
Hier kannst du den Code kopieren und ihn in deinen bevorzugten Editor einfügen. PASTEBIN_DOWNLOAD_SNIPPET_EXPLAIN