smartctl WX32D833J256
von borsti1987- SNIPPET_DESC:
- sudo smartctl -x /dev/sdX
- SNIPPET_CREATION_TIME:
- 12.02.2024 20:26:41
- SNIPPET_PRUNE_TIME:
- 12.05.2024 21:26:41
- SNIPPET_TEXT:
-
- smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-17-amd64] (local build)
- Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Device Model: WDC WD60EFPX-68C5ZN0
- Serial Number: WD-WX32D833J256
- LU WWN Device Id: 5 0014ee 26b61f48d
- Firmware Version: 81.00A81
- User Capacity: 6.001.175.126.016 bytes [6,00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 3.5 inches
- Device is: Not in smartctl database 7.3/5319
- ATA Version is: ACS-3 T13/2161-D revision 5
- SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
- Local Time is: Mon Feb 12 20:04:50 2024 CET
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- AAM feature is: Unavailable
- APM feature is: Unavailable
- Rd look-ahead is: Enabled
- Write cache is: Disabled
- DSN feature is: Unavailable
- ATA Security is: Disabled, NOT FROZEN [SEC1]
- Wt Cache Reorder: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: (61200) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 635) minutes.
- Conveyance self-test routine
- recommended polling time: ( 5) minutes.
- SCT capabilities: (0x3039) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
- 1 Raw_Read_Error_Rate POSR-K 200 165 051 - 0
- 3 Spin_Up_Time POS--K 225 225 021 - 3750
- 4 Start_Stop_Count -O--CK 100 100 000 - 11
- 5 Reallocated_Sector_Ct PO--CK 181 181 140 - 818
- 7 Seek_Error_Rate -OSR-K 100 253 000 - 0
- 9 Power_On_Hours -O--CK 100 100 000 - 119
- 10 Spin_Retry_Count -O--CK 100 253 000 - 0
- 11 Calibration_Retry_Count -O--CK 100 253 000 - 0
- 12 Power_Cycle_Count -O--CK 100 100 000 - 11
- 192 Power-Off_Retract_Count -O--CK 200 200 000 - 4
- 193 Load_Cycle_Count -O--CK 200 200 000 - 25
- 194 Temperature_Celsius -O---K 127 109 000 - 23
- 196 Reallocated_Event_Count -O--CK 194 194 000 - 6
- 197 Current_Pending_Sector -O--CK 200 200 000 - 32
- 198 Offline_Uncorrectable ----CK 100 253 000 - 0
- 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1
- 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
- ||||||_ K auto-keep
- |||||__ C event count
- ||||___ R error rate
- |||____ S speed/performance
- ||_____ O updated online
- |______ P prefailure warning
- General Purpose Log Directory Version 1
- SMART Log Directory Version 1 [multi-sector log support]
- Address Access R/W Size Description
- 0x00 GPL,SL R/O 1 Log Directory
- 0x01 SL R/O 1 Summary SMART error log
- 0x02 SL R/O 5 Comprehensive SMART error log
- 0x03 GPL R/O 6 Ext. Comprehensive SMART error log
- 0x04 GPL R/O 256 Device Statistics log
- 0x04 SL R/O 255 Device Statistics log
- 0x06 SL R/O 1 SMART self-test log
- 0x07 GPL R/O 1 Extended self-test log
- 0x09 SL R/W 1 Selective self-test log
- 0x0c GPL R/O 2048 Pending Defects log
- 0x10 GPL R/O 1 NCQ Command Error log
- 0x11 GPL R/O 1 SATA Phy Event Counters log
- 0x24 GPL R/O 307 Current Device Internal Status Data log
- 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
- 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
- 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
- 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
- 0xb7 GPL,SL VS 78 Device vendor specific log
- 0xbd GPL,SL VS 1 Device vendor specific log
- 0xc0 GPL,SL VS 1 Device vendor specific log
- 0xc1 GPL VS 93 Device vendor specific log
- 0xe0 GPL,SL R/W 1 SCT Command/Status
- 0xe1 GPL,SL R/W 1 SCT Data Transfer
- SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
- Device Error Count: 2083 (device log contains only the most recent 24 errors)
- CR = Command Register
- FEATR = Features Register
- COUNT = Count (was: Sector Count) Register
- LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
- LH = LBA High (was: Cylinder High) Register ] LBA
- LM = LBA Mid (was: Cylinder Low) Register ] Register
- LL = LBA Low (was: Sector Number) Register ]
- DV = Device (was: Device/Head) Register
- DC = Device Control Register
- ER = Error register
- ST = Status register
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 2083 [18] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 e2 7b d8 40 00 Error: UNC at LBA = 0xf9e27bd8 = 4192369624
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 05 40 00 f8 00 00 f9 e3 16 9a 40 08 04:10:46.508 READ FPDMA QUEUED
- 60 05 40 00 c0 00 00 f9 e3 11 5a 40 08 04:10:46.480 READ FPDMA QUEUED
- 60 05 40 00 b8 00 00 f9 e3 0c 1a 40 08 04:10:46.479 READ FPDMA QUEUED
- 60 05 40 00 b0 00 00 f9 e3 06 da 40 08 04:10:46.442 READ FPDMA QUEUED
- 60 05 40 00 a8 00 00 f9 e3 01 9a 40 08 04:10:46.439 READ FPDMA QUEUED
- Error 2082 [17] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 e0 5c 40 40 00 Error: UNC at LBA = 0xf9e05c40 = 4192230464
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 90 00 00 f9 e0 5d 1a 40 08 04:10:32.775 READ FPDMA QUEUED
- 60 00 08 00 88 00 00 f9 e0 5d 12 40 08 04:10:32.775 READ FPDMA QUEUED
- 60 00 08 00 80 00 00 f9 e0 5d 0a 40 08 04:10:32.775 READ FPDMA QUEUED
- 60 00 08 00 78 00 00 f9 e0 5d 02 40 08 04:10:32.775 READ FPDMA QUEUED
- 60 00 08 00 68 00 00 f9 e0 5c fa 40 08 04:10:32.775 READ FPDMA QUEUED
- Error 2081 [16] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 de 5e 78 40 00 Error: UNC at LBA = 0xf9de5e78 = 4192099960
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 50 00 00 f9 de 5f 6a 40 08 04:10:30.163 READ FPDMA QUEUED
- 60 00 08 00 38 00 00 f9 de 5f 62 40 08 04:10:30.163 READ FPDMA QUEUED
- 60 00 08 00 30 00 00 f9 de 5f 5a 40 08 04:10:30.163 READ FPDMA QUEUED
- 60 00 08 00 28 00 00 f9 de 5f 52 40 08 04:10:30.163 READ FPDMA QUEUED
- 60 00 08 00 20 00 00 f9 de 5f 4a 40 08 04:10:30.163 READ FPDMA QUEUED
- Error 2080 [15] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 de 2a 7a 40 00 Error: UNC at LBA = 0xf9de2a7a = 4192086650
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 00 00 00 f9 de 2a a2 40 08 04:10:26.859 READ FPDMA QUEUED
- 60 00 08 00 f8 00 00 f9 de 2a ba 40 08 04:10:26.859 READ FPDMA QUEUED
- 60 00 08 00 f0 00 00 f9 de 2a 9a 40 08 04:10:26.859 READ FPDMA QUEUED
- 60 00 08 00 e8 00 00 f9 de 2a da 40 08 04:10:26.859 READ FPDMA QUEUED
- 60 00 08 00 e0 00 00 f9 de 2b 22 40 08 04:10:26.859 READ FPDMA QUEUED
- Error 2079 [14] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 df 3a 40 40 00 Error: UNC at LBA = 0xf9df3a40 = 4192156224
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 f8 00 00 f9 df 3a 52 40 08 04:10:24.266 READ FPDMA QUEUED
- 60 00 08 00 f0 00 00 f9 de 2a b2 40 08 04:10:24.266 READ FPDMA QUEUED
- 60 00 08 00 e8 00 00 f9 de 2a 7a 40 08 04:10:24.266 READ FPDMA QUEUED
- 60 00 08 00 d8 00 00 f9 de 2a fa 40 08 04:10:24.266 READ FPDMA QUEUED
- 60 00 08 00 d0 00 00 f9 df 3a 4a 40 08 04:10:24.266 READ FPDMA QUEUED
- Error 2078 [13] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 de 2a 78 40 00 Error: UNC at LBA = 0xf9de2a78 = 4192086648
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 b0 00 00 f9 de 2b 6a 40 08 04:10:21.664 READ FPDMA QUEUED
- 60 00 08 00 a8 00 00 f9 de 2b 62 40 08 04:10:21.664 READ FPDMA QUEUED
- 60 00 08 00 30 00 00 f9 de 2b 5a 40 08 04:10:21.619 READ FPDMA QUEUED
- 60 00 08 00 00 00 00 f9 de 2b 52 40 08 04:10:21.619 READ FPDMA QUEUED
- 60 00 08 00 f0 00 00 f9 de 2b 4a 40 08 04:10:21.615 READ FPDMA QUEUED
- Error 2077 [12] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 e0 5c 40 40 00 Error: UNC at LBA = 0xf9e05c40 = 4192230464
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 05 40 00 98 00 00 f9 e0 fa e2 40 08 04:10:13.946 READ FPDMA QUEUED
- 60 05 40 00 d0 00 00 f9 e0 f5 a2 40 08 04:10:13.946 READ FPDMA QUEUED
- 60 05 40 00 10 00 00 f9 e0 f0 62 40 08 04:10:13.945 READ FPDMA QUEUED
- 60 05 40 00 18 00 00 f9 e0 eb 22 40 08 04:10:13.918 READ FPDMA QUEUED
- 60 05 40 00 20 00 00 f9 e0 e5 e2 40 08 04:10:13.909 READ FPDMA QUEUED
- Error 2076 [11] occurred at disk power-on lifetime: 93 hours (3 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 00 00 00 f9 de 5e 78 40 00 Error: UNC at LBA = 0xf9de5e78 = 4192099960
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 05 40 00 b8 00 00 f9 df a0 62 40 08 04:10:08.204 READ FPDMA QUEUED
- 60 05 40 00 b0 00 00 f9 df 9b 22 40 08 04:10:08.204 READ FPDMA QUEUED
- 60 05 40 00 28 00 00 f9 df 95 e2 40 08 04:10:08.201 READ FPDMA QUEUED
- 60 05 40 00 10 00 00 f9 df 51 a2 40 08 04:10:08.187 READ FPDMA QUEUED
- 60 05 40 00 f8 00 00 f9 df 4c 62 40 08 04:10:08.187 READ FPDMA QUEUED
- SMART Extended Self-test Log Version: 1 (1 sectors)
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short offline Completed: read failure 90% 119 4140921728
- # 2 Short offline Completed: read failure 90% 119 4138051880
- # 3 Short offline Completed: read failure 90% 118 4137790872
- # 4 Conveyance offline Completed: read failure 90% 118 4137790872
- # 5 Extended offline Completed: read failure 90% 118 4137790872
- # 6 Short offline Completed: read failure 90% 89 4140921728
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- SCT Status Version: 3
- SCT Version (vendor specific): 258 (0x0102)
- Device State: Active (0)
- Current Temperature: 23 Celsius
- Power Cycle Min/Max Temperature: 23/23 Celsius
- Lifetime Min/Max Temperature: 19/41 Celsius
- Under/Over Temperature Limit Count: 0/0
- Vendor specific:
- 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- SCT Temperature History Version: 2
- Temperature Sampling Period: 1 minute
- Temperature Logging Interval: 1 minute
- Min/Max recommended Temperature: 0/65 Celsius
- Min/Max Temperature Limit: -41/85 Celsius
- Temperature History Size (Index): 478 (421)
- Index Estimated Time Temperature Celsius
- 422 2024-02-12 12:07 30 ***********
- ... ..(376 skipped). .. ***********
- 321 2024-02-12 18:24 30 ***********
- 322 2024-02-12 18:25 ? -
- 323 2024-02-12 18:26 26 *******
- 324 2024-02-12 18:27 26 *******
- 325 2024-02-12 18:28 26 *******
- 326 2024-02-12 18:29 27 ********
- 327 2024-02-12 18:30 27 ********
- 328 2024-02-12 18:31 27 ********
- 329 2024-02-12 18:32 28 *********
- 330 2024-02-12 18:33 28 *********
- 331 2024-02-12 18:34 29 **********
- 332 2024-02-12 18:35 29 **********
- 333 2024-02-12 18:36 28 *********
- 334 2024-02-12 18:37 29 **********
- 335 2024-02-12 18:38 29 **********
- 336 2024-02-12 18:39 ? -
- 337 2024-02-12 18:40 28 *********
- 338 2024-02-12 18:41 27 ********
- 339 2024-02-12 18:42 28 *********
- ... ..( 3 skipped). .. *********
- 343 2024-02-12 18:46 28 *********
- 344 2024-02-12 18:47 29 **********
- ... ..( 18 skipped). .. **********
- 363 2024-02-12 19:06 29 **********
- 364 2024-02-12 19:07 30 ***********
- ... ..( 8 skipped). .. ***********
- 373 2024-02-12 19:16 30 ***********
- 374 2024-02-12 19:17 31 ************
- 375 2024-02-12 19:18 31 ************
- 376 2024-02-12 19:19 31 ************
- 377 2024-02-12 19:20 ? -
- 378 2024-02-12 19:21 31 ************
- ... ..( 9 skipped). .. ************
- 388 2024-02-12 19:31 31 ************
- 389 2024-02-12 19:32 32 *************
- ... ..( 6 skipped). .. *************
- 396 2024-02-12 19:39 32 *************
- 397 2024-02-12 19:40 33 **************
- ... ..( 17 skipped). .. **************
- 415 2024-02-12 19:58 33 **************
- 416 2024-02-12 19:59 ? -
- 417 2024-02-12 20:00 21 **
- 418 2024-02-12 20:01 21 **
- 419 2024-02-12 20:02 22 ***
- 420 2024-02-12 20:03 ? -
- 421 2024-02-12 20:04 23 ****
- SCT Error Recovery Control:
- Read: 70 (7,0 seconds)
- Write: 70 (7,0 seconds)
- Device Statistics (GP Log 0x04)
- Page Offset Size Value Flags Description
- 0x01 ===== = = === == General Statistics (rev 3) ==
- 0x01 0x008 4 11 --- Lifetime Power-On Resets
- 0x01 0x010 4 119 --- Power-on Hours
- 0x01 0x018 6 11721798421 --- Logical Sectors Written
- 0x01 0x020 6 9102975 --- Number of Write Commands
- 0x01 0x028 6 39419565408 --- Logical Sectors Read
- 0x01 0x030 6 31424066 --- Number of Read Commands
- 0x01 0x038 6 428400000 --- Date and Time TimeStamp
- 0x02 ===== = = === == Free-Fall Statistics (rev 1) ==
- 0x02 0x010 4 0 --- Overlimit Shock Events
- 0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
- 0x03 0x008 4 119 --- Spindle Motor Power-on Hours
- 0x03 0x010 4 66 --- Head Flying Hours
- 0x03 0x018 4 30 --- Head Load Events
- 0x03 0x020 4 818 --- Number of Reallocated Logical Sectors
- 0x03 0x028 4 50464 --- Read Recovery Attempts
- 0x03 0x030 4 0 --- Number of Mechanical Start Failures
- 0x03 0x038 4 16016 --- Number of Realloc. Candidate Logical Sectors
- 0x03 0x040 4 4 --- Number of High Priority Unload Events
- 0x04 ===== = = === == General Errors Statistics (rev 1) ==
- 0x04 0x008 4 2009 --- Number of Reported Uncorrectable Errors
- 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
- 0x05 ===== = = === == Temperature Statistics (rev 1) ==
- 0x05 0x008 1 23 --- Current Temperature
- 0x05 0x010 1 31 --- Average Short Term Temperature
- 0x05 0x018 1 - --- Average Long Term Temperature
- 0x05 0x020 1 41 --- Highest Temperature
- 0x05 0x028 1 25 --- Lowest Temperature
- 0x05 0x030 1 37 --- Highest Average Short Term Temperature
- 0x05 0x038 1 31 --- Lowest Average Short Term Temperature
- 0x05 0x040 1 - --- Highest Average Long Term Temperature
- 0x05 0x048 1 - --- Lowest Average Long Term Temperature
- 0x05 0x050 4 0 --- Time in Over-Temperature
- 0x05 0x058 1 65 --- Specified Maximum Operating Temperature
- 0x05 0x060 4 0 --- Time in Under-Temperature
- 0x05 0x068 1 0 --- Specified Minimum Operating Temperature
- 0x06 ===== = = === == Transport Statistics (rev 1) ==
- 0x06 0x008 4 49 --- Number of Hardware Resets
- 0x06 0x010 4 24 --- Number of ASR Events
- 0x06 0x018 4 1 --- Number of Interface CRC Errors
- 0xff ===== = = === == Vendor Specific Statistics (rev 1) ==
- 0xff 0x008 7 0 --- Vendor Specific
- 0xff 0x010 7 0 --- Vendor Specific
- 0xff 0x018 7 0 --- Vendor Specific
- |||_ C monitored condition met
- ||__ D supports DSN
- |___ N normalized value
- Pending Defects log (GP Log 0x0c)
- Index LBA Hours
- 0 4134499336 -
- 1 4134499337 -
- 2 4134499338 -
- 3 4134499339 -
- 4 4134499340 -
- 5 4134499341 -
- 6 4134499342 -
- 7 4134499343 -
- 8 4134844680 -
- 9 4134844681 -
- 10 4134844682 -
- 11 4134844683 -
- 12 4134844684 -
- 13 4134844685 -
- 14 4134844686 -
- 15 4134844687 -
- 16 4137790872 -
- 17 4137790873 -
- 18 4137790874 -
- 19 4137790875 -
- 20 4137790876 -
- 21 4137790877 -
- 22 4137790878 -
- 23 4137790879 -
- 24 4137799528 -
- 25 4137799529 -
- 26 4137799530 -
- 27 4137799531 -
- 28 4137799532 -
- 29 4137799533 -
- 30 4137799534 -
- ... (225 entries not shown)
- SATA Phy Event Counters (GP Log 0x11)
- ID Size Value Description
- 0x0001 2 0 Command failed due to ICRC error
- 0x0002 2 0 R_ERR response for data FIS
- 0x0003 2 0 R_ERR response for device-to-host data FIS
- 0x0004 2 0 R_ERR response for host-to-device data FIS
- 0x0005 2 0 R_ERR response for non-data FIS
- 0x0006 2 0 R_ERR response for device-to-host non-data FIS
- 0x0007 2 0 R_ERR response for host-to-device non-data FIS
- 0x0008 2 0 Device-to-host non-data FIS retries
- 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
- 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
- 0x000b 2 0 CRC errors within host-to-device FIS
- 0x000d 2 0 Non-CRC errors within host-to-device FIS
- 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
- 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
- 0x8000 4 8 Vendor specific
Quellcode
Hier kannst du den Code kopieren und ihn in deinen bevorzugten Editor einfügen. PASTEBIN_DOWNLOAD_SNIPPET_EXPLAIN