folgende Anleitung habe ich befolgt.
https://wiki.debian.org/ATIProprietary
laut
lspci -v
Code: Alles auswählen
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Hawaii PRO [Radeon R9 290] (prog-if 00 [VGA controller])
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 0b00
Flags: bus master, fast devsel, latency 0, IRQ 49
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at ef800000 (64-bit, prefetchable) [size=8M]
I/O ports at ee00 [size=256]
Memory at fdc80000 (32-bit, non-prefetchable) [size=256K]
[virtual] Expansion ROM at fdc00000 [disabled] [size=128K]
Capabilities: [48] Vendor Specific Information: Len=08 <?>
Capabilities: [50] Power Management version 3
Capabilities: [58] Express Legacy Endpoint, MSI 00
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [150] Advanced Error Reporting
Capabilities: [270] #19
Capabilities: [2b0] Address Translation Service (ATS)
Capabilities: [2c0] #13
Capabilities: [2d0] #1b
Kernel driver in use: fglrx_pci
per amdccle ->
Code: Alles auswählen
amdcccle
No protocol specified
amdcccle: cannot connect to X server :0
root@derpian:/home/christoph# aticonfig --pplib-cmd "set fanspeed 0 100"
No protocol specified
No layout section was found in the file: '/etc/X11/xorg.conf'.
Please run 'aticonfig --initial' first or modify your configuration file manually and run aticonfig again.
aticonfig: parsing the command-line failed.
habe es "per hand" mit dem echo befehl gemacht.
Code: Alles auswählen
# mkdir /etc/X11/xorg.conf.d
# echo -e 'Section "Device"\n\tIdentifier "My GPU"\n\tDriver "fglrx"\nEndSection' > /etc/X11/xorg.conf.d/20-fglrx.conf
Bei 3d_beschleuniger zeigt er mir unbekannt an und bei Kernelmodul ebenso. Und auf anhieb finde ich kein vergleichsscreenshot.
fglrx-control habe ich nachinstallieren müssen, aber dieser scheint nicht vorhanden zu sein.
Neugestartet habe ich mein System nach der Treiber Installation.
Code: Alles auswählen
[ 4.148]
X.Org X Server 1.16.4
Release Date: 2014-12-20
[ 4.148] X Protocol Version 11, Revision 0
[ 4.148] Build Operating System: Linux 3.16.0-4-amd64 x86_64 Debian
[ 4.148] Current Operating System: Linux derpian 3.16.0-4-amd64 #1 SMP Debian 3.16.39-1+deb8u1 (2017-02-22) x86_64
[ 4.148] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-amd64 root=UUID=f64b1b57-dc8c-4a10-bb5d-a0b40c9bd33d ro quiet
[ 4.148] Build Date: 11 February 2015 12:32:02AM
[ 4.148] xorg-server 2:1.16.4-1 (http://www.debian.org/support)
[ 4.148] Current version of pixman: 0.32.6
[ 4.148] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 4.148] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 4.148] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Feb 27 14:46:59 2017
[ 4.148] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 4.148] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
Was mir noch auffällt. In eurem Wiki werden keine Header dateien mit installiert. Laut debian.org Wiki sind diese aber nötig (?) (Ist das Wiki in dem Punkt "alt"?)
sollte ich
Code: Alles auswählen
aticonfig --initial