Leider ist immer einer der TFT deaktiviert, wenn ich mich einlogge. Im NVidia-Konfigurationstool werden alle 3 Monitore erkannt, aber ich bekomme es da nicht konfiguriert. Mit der xorg.conf habe ich xscreen konfiguriert, es werden aber immer nur 2 angezeigt.
Ich hoffe, die Karte kann alle 3 Ausgänge mit Monitoren daran ansteuern.
Hier die "lspci -v" Ausgabe von der GraKa:
Code: Alles auswählen
04:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 210] (rev a2) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. [MSI] N210 [ ] PCIe graphics adapter
Flags: bus master, fast devsel, latency 0, IRQ 33
Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Memory at e0000000 (64-bit, prefetchable) [size=256M]
Memory at f0000000 (64-bit, prefetchable) [size=32M]
I/O ports at e000 [size=128]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [b4] Vendor Specific Information: Len=14 <?>
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nvidia
Kernel modules: nvidia
Code: Alles auswählen
Section "Monitor"
Identifier "DELL00"
ModelName "DELL P2210t"
VendorName "DELL"
Option "DPMS" "true"
Horizsync 30-83
VertRefresh 56-75
EndSection
Section "Monitor"
Identifier "DELL01"
ModelName "DELL P2210t"
VendorName "DELL"
Option "DPMS" "true"
Horizsync 30-83
VertRefresh 56-75
EndSection
Section "Monitor"
Identifier "DELL02"
ModelName "DELL P2210t"
VendorName "DELL"
Option "DPMS" "true"
Horizsync 30-83
VertRefresh 56-75
EndSection
Section "DRI"
Mode 0666
EndSection
Section "Device"
Identifier "NVIDIA GT218 GeForce 210 00"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GT218 GeForce 210"
BusID "PCI:4:0:0"
Option "NoLogo" "True"
Screen 0
EndSection
Section "Device"
Identifier "NVIDIA GT218 GeForce 210 01"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GT218 GeForce 210"
BusID "PCI:4:0:0"
Option "NoLogo" "True"
Screen 1
EndSection
Section "Device"
Identifier "NVIDIA GT218 GeForce 210 02"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GT218 GeForce 210"
BusID "PCI:4:0:0"
Option "NoLogo" "True"
Screen 2
EndSection
Section "Module"
Load "glx"
EndSection
Section "Screen"
Identifier "Screen00"
Device "NVIDIA GT218 GeForce 210 00"
Monitor "DELL00"
Option "metamodes" "DFP-0: 1680x1050 +0+0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1680x1050"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen01"
Device "NVIDIA GT218 GeForce 210 01"
Monitor "DELL01"
Option "metamodes" "DFP-1: 1680x1050 +0+0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1680x1050"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen02"
Device "NVIDIA GT218 GeForce 210 02"
Monitor "DELL02"
Option "metamodes" "CRT-1: 1680x1050 +0+0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1680x1050"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default"
Screen "Screen00" 0 0
Screen "Screen01" LeftOf "Screen00"
Screen "Screen02" RightOf "Screen00"
Option "Xinerama" "0"
Option "NoLogo" "true"
EndSection
Was ist falsch in der xorg.conf?