WLAN funktioniert nicht Aspire E 15

Einrichten des lokalen Netzes, Verbindung zu anderen Computern und Diensten.
geier22

WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 09:25:02

hab mir einen Acer Aspire E 15 - E5-575G-56WG zugelegt, Stretch XFCE installiert und habe ein WIFI Problem:
Es funktioniert nicht. :oops:
Es wird zwar im Netzwerk-Manager angezeigt, eine Verbindung kann aber nicht hergestellt werden.
Firmware jeglicher Art, sollte installiert sein
Diagnosen, soweit mir bekannt:

Code: Alles auswählen

# dmesg |grep fail
[    0.458249] platform MSFT0101:00: failed to claim resource 1
[    0.458307] acpi MSFT0101:00: platform device creation failed: -16
[    3.858220] acer_wmi: Enabling Launch Manager failed: 0xe4 - 0x0
[    4.191176] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:03:00.0.bin (-2)
[    4.191178] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:03:00.0.bin failed with error -2
[    4.191184] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/cal-pci-0000:03:00.0.bin (-2)
[    4.191185] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/cal-pci-0000:03:00.0.bin failed with error -2
[    4.402308] bbswitch: module verification failed: signature and/or required key missing - tainting kernel

Code: Alles auswählen

# lspci -nnk | grep -i net -A2
03:00.0 Network controller [0280]: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter [168c:0042] (rev 31)
	Subsystem: Lite-On Communications Inc QCA9377 802.11ac Wireless Network Adapter [11ad:08a6]
	Kernel driver in use: ath10k_pci
	Kernel modules: ath10k_pci
--
04:00.1 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 12)
	Subsystem: Acer Incorporated [ALI] RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [1025:1094]
	Kernel driver in use: r8169
	Kernel modules: r8169

Code: Alles auswählen

# iwconfig
wlan0     IEEE 802.11  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:on
          
lo        no wireless extensions.

eth0      no wireless extensions.
Mein Netzwerk:

Code: Alles auswählen

# iwlist scan
wlan0     Scan completed :
              Cell 12 - Address: xx:xx:xx:xx:xx:xx
                    Channel:1
                    Frequency:2.412 GHz (Channel 1)
                    Quality=66/70  Signal level=-44 dBm  
                    Encryption key:on
                    ESSID:"XXXXX"
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s
                    Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
                    Mode:Master
                    Extra:tsf=00000451077b9374
                    Extra: Last beacon: 4400ms ago
                    IE: Unknown: 000741617262757267
                    IE: Unknown: 010882848B968C129824
                    IE: Unknown: 030101
                    IE: Unknown: 0706444520010D14
                    IE: Unknown: 2A0100
                    IE: Unknown: 3204B048606C
                    IE: Unknown: 2D1AEE111BFFFF000000000000000000008000000000000000000000
                    IE: Unknown: 331AEE111BFFFF000000000000000000008000000000000000000000
                    IE: Unknown: 3D1601000500000000000000000000000000000000000000
                    IE: Unknown: 341601000500000000000000000000000000000000000000
                    IE: Unknown: 4A0E14000A002C01C800140005001900
                    IE: Unknown: 7F050100000000
                    IE: Unknown: DD180050F2020101010003A4000027A4000042435E0062322F00
                    IE: Unknown: DD0900037F01010000FF7F
                    IE: Unknown: DD0C00040E010102010000000000
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : CCMP
                        Authentication Suites (1) : PSK
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK
  • dpkg -l |grep firmware*
    ii amd64-microcode 3.20160316.3 amd64 Processor microcode firmware for AMD CPUs
    ii atmel-firmware 1.3-4 all Firmware for Atmel at76c50x wireless networking chips.
    ii b43-fwcutter 1:019-3 amd64 utility for extracting Broadcom 43xx firmware
    ii bluez-firmware 1.2-3 all Firmware for Bluetooth devices
    ii firmware-amd-graphics 20161130-2 all Binary firmware for AMD/ATI graphics chips
    ii firmware-atheros 20161130-2 all Binary firmware for Atheros wireless cards
    ii firmware-b43-installer 1:019-3 all firmware installer for the b43 driver
    ii firmware-b43legacy-installer 1:019-3 all firmware installer for the b43legacy driver
    ii firmware-bnx2 20161130-2 all Binary firmware for Broadcom NetXtremeII
    ii firmware-bnx2x 20161130-2 all Binary firmware for Broadcom NetXtreme II 10Gb
    ii firmware-brcm80211 20161130-2 all Binary firmware for Broadcom 802.11 wireless cards
    ii firmware-crystalhd 0.0~git20120110.fdd2f19-1 all Crystal HD Video Decoder (firmware)
    ii firmware-intelwimax 20161130-2 all Binary firmware for Intel WiMAX Connection
    ii firmware-ipw2x00 20161130-2 all Binary firmware for Intel Pro Wireless 2100, 2200 and 2915
    ii firmware-ivtv 20161130-2 all Binary firmware for iTVC15-family MPEG codecs (ivtv and pvrusb2 drivers)
    ii firmware-iwlwifi 20161130-2 all Binary firmware for Intel Wireless cards
    ii firmware-libertas 20161130-2 all Binary firmware for Marvell wireless cards
    ii firmware-linux 20161130-2 all Binary firmware for various drivers in the Linux kernel (meta-package)
    ii firmware-linux-free 3.4 all Binary firmware for various drivers in the Linux kernel
    ii firmware-linux-nonfree 20161130-2 all Binary firmware for various drivers in the Linux kernel (meta-package)
    ii firmware-misc-nonfree 20161130-2 all Binary firmware for various drivers in the Linux kernel
    ii firmware-myricom 20161130-2 all Binary firmware for Myri-10G Ethernet adapters
    ii firmware-netxen 20161130-2 all Binary firmware for QLogic Intelligent Ethernet (3000 and 3100 Series)
    ii firmware-qlogic 20161130-2 all Binary firmware for QLogic HBAs
    ii firmware-realtek 20161130-2 all Binary firmware for Realtek wired/wifi/BT adapters
    ii firmware-ti-connectivity 20161130-2 all Binary firmware for TI Connectivity wifi and BT/FM/GPS adapters
    ii firmware-zd1211 1:1.5-4 all binary firmware for the zd1211rw wireless driver
    ii intel-microcode 3.20161104.1 amd64 Processor microcode firmware for Intel CPUs
    ii isight-firmware-tools 1.6-2+b2 amd64 tools for dealing with Apple iSight firmware
    ii libertas-firmware 9.70.7.p0.0-2 all Firmware for Marvell's libertas wireless chip series (dummy package)
    ii linux-wlan-ng-firmware 0.2.9+dfsg-5 all firmware files used by the linux-wlan-ng driver
    ii prism2-usb-firmware-installer 0.2.9+dfsg-5 amd64 firmware files for the prism2_usb kernel driver
    ii zd1211-firmware 3.0.0.56-4 all transitional dummy package for firmware-zd1211
Hab im Netz einen Lösungsansatz gefungen, den aber noch nicht ausprobiert, weil ich mir nicht sicher bin, was ich mir da alles zerschieße.
https://digitz.org/blog/wifi-issue-on-a ... vice-0042/

Habt Ihr eine Lösung ? :hail:

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 15:15:56

hmmmmm..

Hab weiter versucht vielleicht hat dann jemand eine Idee:

Fritz!Box mit unverschlüsseltem Gastzugang ------> Funktioniert
Gastzugang abgeschaltet:

Die letzten Zeilen:

Code: Alles auswählen

# dmesg
751.008908] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  751.011398] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  783.012501] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  783.072089] wlan0: authenticate with 9c:c7:a6:57:f9:52
[  783.104229] wlan0: send auth to 9c:c7:a6:57:f9:52 (try 1/3)
[  783.209382] wlan0: send auth to 9c:c7:a6:57:f9:52 (try 2/3)
[  783.313384] wlan0: send auth to 9c:c7:a6:57:f9:52 (try 3/3)
[  783.417280] wlan0: authentication with 9c:c7:a6:57:f9:52 timed out
[  783.442530] ath10k_warn: 50 callbacks suppressed
[  783.442539] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.442983] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.524479] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.527874] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.530900] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.544932] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.545431] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.626987] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.630276] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  783.633201] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
Ich werde daraus einfach nicht schlau :| :|

hier noch die komplette Ausgabe von dmesg: NoPaste-Eintrag39814

Code: Alles auswählen

ip -s l
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    RX: bytes  packets  errors  dropped overrun mcast   
    1233466    1767     0       0       0       0       
    TX: bytes  packets  errors  dropped carrier collsns 
    1233466    1767     0       0       0       0       
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 54:ab:3a:f6:76:81 brd ff:ff:ff:ff:ff:ff
    RX: bytes  packets  errors  dropped overrun mcast   
    573615     1741     0       0       0       22      
    TX: bytes  packets  errors  dropped carrier collsns 
    469262     1835     0       0       0       0       
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT group default qlen 1000
    link/ether 94:e9:79:ab:0a:fd brd ff:ff:ff:ff:ff:ff
    RX: bytes  packets  errors  dropped overrun mcast   
    0          0        0       0       0       0       
    TX: bytes  packets  errors  dropped carrier collsns 
    0          0        0       0       0       0     

Benutzeravatar
MSfree
Beiträge: 10683
Registriert: 25.09.2007 19:59:30

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von MSfree » 24.04.2017 15:49:43

geier22 hat geschrieben:hier noch die komplette Ausgabe von dmesg: NoPaste-Eintrag39814
Da steht do klipp und klar in Zeile 26:

Code: Alles auswählen

[    4.200662] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:03:00.0.bin (-2)
Der findet die Datei pre-cal-pci-0000:03:00.0.bin nicht. Wenn man diesen Dateinamen bei google eingibt, bekommt man aus verschiedenen Foren die Information, daß man da wohl eine Firmwaredatei umbenennen muß, damit sie geladen wird.

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 16:23:03

hmmm
von Hier:http://forums.debian.net/viewtopic.php?f=7&t=127880

Code: Alles auswählen

My wifi card is working now!
Inside /lib/firmware/ath10k I found hw1.0 folder with drivers in it, but ath10 was looking for firmware inside /lib/firmware/ath10k/QCA9377/hw1.0/ so I just created directory QCA9377 and moved hw1.0 to it, rebooted and is working now. Thanks for your help.
sieht doch bei mir genau so aus:

Code: Alles auswählen

/lib/firmware/ath10k/QCA9377/hw1.0$ ls
board-2.bin  board.bin  firmware-5.bin
MSfree hat geschrieben:Der findet die Datei pre-cal-pci-0000:03:00.0.bin nicht.
Welche soll das den sein ?

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 17:23:48

Code: Alles auswählen

root@aspire:/home/hans# dmesg |grep ath10k
[    3.976409] ath10k_pci 0000:03:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    4.267774] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:03:00.0.bin (-2)
[    4.267784] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:03:00.0.bin failed with error -2
[    4.267808] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/cal-pci-0000:03:00.0.bin (-2)
[    4.267813] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/cal-pci-0000:03:00.0.bin failed with error -2
[    4.270291] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/firmware-5.bin
[    4.270304] ath10k_pci 0000:03:00.0: qca9377 hw1.1 target 0x05020001 chip_id 0x003821ff sub 11ad:08a6
[    4.270308] ath10k_pci 0000:03:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[    4.271506] ath10k_pci 0000:03:00.0: firmware ver WLAN.TF.1.0-00267-1 api 5 features ignore-otp crc32 79cea2c7
[    4.339334] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/board-2.bin
[    4.339805] ath10k_pci 0000:03:00.0: board_file api 2 bmi_id N/A crc32 93da0176
[    6.165124] ath10k_pci 0000:03:00.0: htt-ver 3.1 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1

Kommentar : Verbindungs- Versuch:

[   15.382505] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[   44.107032] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[   91.957314] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[   96.718934] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[   96.741834] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[   96.751903] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[   96.754833] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[   96.769374] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.554572] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.567220] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.569834] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.582310] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.634141] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.656259] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.684745] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.736561] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.758790] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  101.769656] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  106.856454] ath10k_warn: 14 callbacks suppressed
[  106.856471] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  106.879055] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  106.889692] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  106.892292] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  106.907151] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  106.958871] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  106.983443] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  107.009562] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  107.061233] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  107.083874] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.590872] ath10k_warn: 25 callbacks suppressed
[  112.590888] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.613507] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.626868] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.641960] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.693551] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.715817] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.729075] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.731678] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.743986] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[  112.795668] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
root@aspire:/home/hans# 
4.339334] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/board-2.bin
es scheinen doch aber dann die Treiber geladen zu werden ?

Was bedeuten diese Zeilen, wenn eine Verbindung über einen unverschlüsselten Gast- Zugang doch funktioniert ??
ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 18:14:44

Gastzugang unverschlüsselt:

Code: Alles auswählen

iwconfig
eth0      no wireless extensions.

lo        no wireless extensions.

wlan0     IEEE 802.11  ESSID:"FRITZ!Box Gastzugang"  
          Mode:Managed  Frequency:2.412 GHz  Access Point: 82:C7:A6:57:F9:52   
          Bit Rate=1 Mb/s   Tx-Power=20 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:on
          Link Quality=63/70  Signal level=-47 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:1   Missed beacon:0
Warum funktioniert der Gastzugang und der verschlüsselte (WPA & WPA2 Personal) nicht :facepalm: :|

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 24.04.2017 20:03:22

Warum funktioniert der Gastzugang und der verschlüsselte (WPA & WPA2 Personal) nicht :facepalm: :|
Weil du offensichtlich nicht das tust, was MSFree geschrieben hat! :wink:
My wifi card is working now!
Inside /lib/firmware/ath10k I found hw1.0 folder with drivers in it, but ath10 was looking for firmware inside /lib/firmware/ath10k/QCA9377/hw1.0/ so I just created directory QCA9377 and moved hw1.0 to it, rebooted and is working now. Thanks for your help.
http://forums.debian.net/viewtopic.php? ... 80#p612539

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 20:09:36

@jana66
geier22 hat geschrieben:von Hier:http://forums.debian.net/viewtopic.php?f=7&t=127880

Code: Alles auswählen
My wifi card is working now!
Inside /lib/firmware/ath10k I found hw1.0 folder with drivers in it, but ath10 was looking for firmware inside /lib/firmware/ath10k/QCA9377/hw1.0/ so I just created directory QCA9377 and moved hw1.0 to it, rebooted and is working now. Thanks for your help.


sieht doch bei mir genau so aus:

Code: Alles auswählen
/lib/firmware/ath10k/QCA9377/hw1.0$ ls
board-2.bin board.bin firmware-5.bin
Bin ich blind ? Der gute hat doch das gemacht, was bei mir schon vorhanden ist.

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 24.04.2017 20:26:44

Oh sorry, ich habe das $-Zeichen als (falsches) Ende des Verzeichnisnamens interpretiert. :facepalm:

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 24.04.2017 20:43:50

Schau mal ob i. O.

Code: Alles auswählen

iw dev wlan0
iw dev wlan0 station dump
Ob das so korrekt ist, weiss ich nicht:
[ 4.267813] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/cal-pci-0000:03:00.0.bin failed with error -2
[ 4.270291] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/firmware-5.bin
Irgendein Ersatz bei fail?

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 21:11:15

Code: Alles auswählen

iw dev wlan0
gibt Fehler NoPaste-Eintrag39815

Code: Alles auswählen

 iw phy0 info
ergibt NoPaste-Eintrag39816

Code: Alles auswählen

root@aspire:/home/hans# iw dev wlan0 station dump
root@aspire:/home/hans# 
nix

Code: Alles auswählen

# iw dev
phy#0
	Unnamed/non-netdev interface
		wdev 0x2
		addr 94:e9:79:ab:0a:fd
		type P2P-device
		txpower 0.00 dBm
	Interface wlan0
		ifindex 3
		wdev 0x1
		addr 4e:76:b5:69:3e:5f
		type managed
		txpower 20.00 dBm
Ich hab ziemlich wenig Ahnung mit dem WLAN Zeugs aber ich habe den Verdacht, das es an der Verschlüsselung liegen könnte.
Warum funktioniert sonst der unverschlüsselte Gastzugang ohne Probleme??

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 21:25:03

so hab nochmal einen Test gemacht:
Gastzugang mit WPA2 verschlüsselt ---> nix geht
Gastzugang unverschlüsselt: Funktioniert prächtig (bin gerade damit unterwegs)

fällt allerdings zwischendurch aus :oops: :oops:

Code: Alles auswählen

iw dev
phy#0
	Unnamed/non-netdev interface
		wdev 0x3
		addr 94:e9:79:ab:0a:fd
		type P2P-device
		txpower 0.00 dBm
	Interface wlan0
		ifindex 3
		wdev 0x1
		addr 94:e9:79:ab:0a:fd
		type managed
		channel 1 (2412 MHz), width: 40 MHz, center1: 2422 MHz
		txpower 20.00 dBm
root@aspire:/home/hans# 

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 24.04.2017 21:35:32

Versuche erst mal, nur auf 2,4 GHz 802.11g oder n zu verbinden. Machst du wohl schon. Und dann mal so schauen:

Code: Alles auswählen

iwevent
iw event
iw event -f          # erweiterte Ausgabe mit Fehlermeldungen zum Verbindungsstatus
iw event -t          # erweiterte Ausgabe mit Fehlermeldungen und Zeitangaben (timing)
iw event -r          # erweiterte Ausgabe mit Fehlermeldungen und relativen Zeitangaben 
Wenn mit den Kommandos was nicht klappt, mal hier schauen
https://wiki.ubuntuusers.de/iw/
oder eben manpage. Bin derzeit nicht am PC.

Warum nutzt du Gastzugang und nicht den normalen? Du willst den Debian-Lappi schon mit einen WLAN-Router verbinden? Oder etwa einen Accesspoint für andere Clients (Smartphone oder so) erstellen?
Welcher WLAN-Router?

Und poste noch mal ein

Code: Alles auswählen

iwlist scan
Alle SSIDs wegen Interferenzen! Sind bestimmt noch einge auf deinem Kanal 1. :wink:

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 23:05:39

fang ich mal von hinten an:
iwlist scan ----> NoPaste-Eintrag39817

iwevent
Gastzugang (unverschlüsselt) aufbauen --> trennen --> aufbauen

Code: Alles auswählen

root@aspire:/home/hans# iwevent
Waiting for Wireless Events from interfaces...
22:27:22.139388   wlan0    New Access Point/Cell address:Not-Associated
22:27:26.561929   wlan0    Scan request completed
22:27:29.929800   wlan0    Association Response IEs:010882848B0C1296182432043048606C2D1AEE111BFFFF000000000000000000008000000000000000000000331AEE111BFFFF0000000000000000000080000
22:27:29.929934   wlan0    New Access Point/Cell address:82:C7:A6:57:F9:52
22:27:56.265635   wlan0    Scan request completed
22:28:39.273914   wlan0    Scan request completed
22:29:42.250039   wlan0    Scan request completed
22:31:05.092985   wlan0    Scan request completed
22:32:30.802221   wlan0    Scan request completed
22:32:48.315171   wlan0    Scan request completed
22:33:34.131532   wlan0    New Access Point/Cell address:Not-Associated
22:33:37.940328   wlan0    Scan request completed
22:33:45.484675   wlan0    Scan request completed
22:33:45.530726   wlan0    Association Response IEs:010882848B0C1296182432043048606C2D1AEE111BFFFF000000000000000000008000000000000000000000331AEE111BFFFF0000000000000000000080000
22:33:45.530822   wlan0    New Access Point/Cell address:82:C7:A6:57:F9:52
iw event -f (Verbindungsversuch mit normalen - verschlüsseltem Zugang)

Code: Alles auswählen

root@aspire:/home/hans# iw event -f
wlan0 (phy #0): scan started
wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825, "Aarburg" ""
wlan0: new station 9c:c7:a6:57:f9:52
wlan0: del station 9c:c7:a6:57:f9:52
wlan0 (phy #0): auth 9c:c7:a6:57:f9:52 -> 94:e9:79:ab:0a:fd status: 37: The request has been declined [frame: b0 00 3a 01 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 9c c7 a6 57 f9 52 00 10 00 00 02 00 25 00]
wlan0 (phy #0): scan started
wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825, "Aarburg" ""
wlan0: new station 9c:c7:a6:57:f9:52
wlan0: del station 9c:c7:a6:57:f9:52
wlan0 (phy #0): auth 9c:c7:a6:57:f9:52 -> 94:e9:79:ab:0a:fd status: 37: The request has been declined [frame: b0 00 3a 01 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 9c c7 a6 57 f9 52 00 10 00 00 02 00 25 00]
wlan0 (phy #0): scan started
wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825, ""
wlan0 (phy #0): scan started
wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825, ""
^C 
dasselbe mit dmesg:

Code: Alles auswählen

[ 2336.019388] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2651.067799] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2714.066026] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 2966.065645] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3281.010481] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3344.069424] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3407.136973] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3407.599666] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3533.317417] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3543.498804] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3547.943396] wlan0: authenticate with 9c:c7:a6:57:f9:52
[ 3547.975450] wlan0: send auth to 9c:c7:a6:57:f9:52 (try 1/3)
[ 3547.978750] wlan0: 9c:c7:a6:57:f9:52 denied authentication (status 37)
[ 3548.002108] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.003211] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.040508] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.054465] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.074428] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.104478] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.105542] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.136067] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.142815] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3548.156847] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.019652] ath10k_warn: 270 callbacks suppressed
[ 3553.019675] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.020755] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.048939] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.058100] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.072028] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.123190] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.160515] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.174385] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.193587] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3553.224498] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.409659] wlan0: authenticate with 9c:c7:a6:57:f9:52
[ 3562.442343] wlan0: send auth to 9c:c7:a6:57:f9:52 (try 1/3)
[ 3562.447317] wlan0: 9c:c7:a6:57:f9:52 denied authentication (status 37)
[ 3562.478774] ath10k_warn: 275 callbacks suppressed
[ 3562.478790] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.492911] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.502967] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.505665] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.542873] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.551640] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.581268] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.595502] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.645268] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
[ 3562.683686] ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
root@aspire:/home/hans# 
Jana66 hat geschrieben:Welcher WLAN-Router?
Fritz!Box 7330 mit Fritz!Os 06.53
Jana66 hat geschrieben:Warum nutzt du Gastzugang und nicht den normalen?
Weil ich mit dem "normalen" (verschlüsselten) es bisher nicht zustande bekommen habe
Jana66 hat geschrieben:Du willst den Debian-Lappi schon mit einen WLAN-Router verbinden
Ja - das ist zwar bei mir zu Hause nicht zwingend notwendig, aber auf der Arbeit brauche ich es
Jana66 hat geschrieben:Oder etwa einen Accesspoint für andere Clients (Smartphone oder so) erstellen?
Nee - mein Smartphone ist zu Hause per default mit dem WLAN verbunden

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 24.04.2017 23:24:52

Hols der TEUFEL --- JETZT KLAPPT ES :facepalm: :mrgreen:
Mal sehen wie lange

Code: Alles auswählen

root@aspire:/home/hans# iw event -f
wlan0: del station 9c:c7:a6:57:f9:52
wlan0 (phy #0): deauth 94:e9:79:ab:0a:fd -> 9c:c7:a6:57:f9:52 reason 3: Deauthenticated because sending station is leaving (or has left) the IBSS or ESS [frame: c0 00 00 00 9c c7 a6 57 f9 52 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 00 00 03 00]
wlan0 (phy #0): disconnected (local request)
phy #0: regulatory domain change: set to world roaming by the wireless core upon initialization request
wlan0 (phy #0): scan started
phy #0: beacon hint:
phy0 5180 MHz [36]:
	o Initiating radiation enabled
wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825, ""
wlan0 (phy #0): scan started
wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825, "Aarburg" ""
wlan0: new station 9c:c7:a6:57:f9:52
wlan0 (phy #0): auth 9c:c7:a6:57:f9:52 -> 94:e9:79:ab:0a:fd status: 0: Successful [frame: b0 00 3a 01 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 9c c7 a6 57 f9 52 00 10 00 00 02 00 00 00]
wlan0 (phy #0): assoc 9c:c7:a6:57:f9:52 -> 94:e9:79:ab:0a:fd status: 0: Successful [frame: 10 00 3a 01 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 9c c7 a6 57 f9 52 20 10 31 04 00 00 02 c0 01 08 82 84 8b 0c 12 96 18 24 32 04 30 48 60 6c 2d 1a ee 11 1b ff ff 00 00 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 33 1a ee 11 1b ff ff 00 00 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 3d 16 01 05 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 34 16 01 05 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4a 0e 14 00 0a 00 2c 01 c8 00 14 00 05 00 19 00 7f 05 01 00 00 00 00 dd 18 00 50 f2 02 01 01 02 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00]
wlan0 (phy #0): connected to 9c:c7:a6:57:f9:52
phy #0: regulatory domain change: set to DE by a country IE request on phy0
wlan0 (phy #0): scan started
wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825, ""

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 25.04.2017 07:37:43

Guten Morgen, Hans!
geier22 hat geschrieben:iwlist scan ----> NoPaste-Eintrag 39817
Ganz hübsch voll, euer WLAN.
Auf Kanal 1 kannst du bleiben. Ist zwar noch einer drauf, aber der ist genau drauf. Dessen Traffic verringert Bandbreite, macht aber keine Interferenzen, da die Sender sich gegenseitig erkennen.
Du sendest mit:

Code: Alles auswählen

Frequency:2.412 GHz (Channel 1)
                    Quality=64/70  Signal level=-46 dBm  
                    Encryption key:off
                    ESSID:"FRITZ!Box Gastzugang"
und

Code: Alles auswählen

Frequency:2.412 GHz (Channel 1)
                    Quality=64/70  Signal level=-46 dBm  
                    Encryption key:on
                    ESSID:"Aarburg"
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s
                    Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Fremd:

Code: Alles auswählen

Frequency:2.412 GHz (Channel 1)
                    Quality=37/70  Signal level=-73 dBm  
                    Encryption key:on
                    ESSID:"Kelevra"
Der Rest ist ziemlich besetzt.

Ich empfehle dir das Programm linssid für Kanalplanung/Übersicht. Ist nicht in Paketquellen.
Des Weiteren könntest du später, wenn alles läuft, am Router 802.11n für 2,4 GHz einstellen sowie aufgrund der vielen WLANs auf 5 GHz 802.11n oder ac umsteigen bzw. zusätzlich nutzen. 5 GHz hat eine viel geringere Reichweite aufgrund höherer Dämpfung.
iw event -f (Verbindungsversuch mit normalen - verschlüsseltem Zugang)
Sagt nicht viel aus, da warst du gestern mein Versuchskaninchen. (Kommandos gestern neu entdeckt. :wink: )
dasselbe mit dmesg:
sagt schon mehr und nichts Gutes.
schon in deinem ersten Post:

Code: Alles auswählen

8.078746] pcieport 0000:00:1d.2: can't find device of ID00ea
[    8.078747] pcieport 0000:00:1d.2: AER: Multiple Corrected error received: id=00ea
[    8.078750] pcieport 0000:00:1d.2: can't find device of ID00ea
[    8.078751] pcieport 0000:00:1d.2: AER: Multiple Corrected error received: id=00ea
[    8.078773] pcieport 0000:00:1d.2: can't find device of ID00ea
Woher das kommt, weiß ich nicht. Wir machen vlt. mal so weiter - zum Fehlerausschluss (Hardware oder so):

Test deines WlANs/Laptops mit Live Iso und modernem Ubuntu oder Mint.

Dann macht ihr ollen Debian-Hasen (oder -Geier) doch oft Minimalinstallation. Du auch? Also mal eine Live-Debian und Treiber nachinstallieren. Eventuell auch mal auf einem Stückchen Festplatte eine Komplettinstallation gleich mit nonfree netinstall. Wie für Anfänger empfohlen. :mrgreen:
Hols der TEUFEL --- JETZT KLAPPT ES :facepalm: :mrgreen:
Sporadische Fehler sind die schlimmsten! Ich würde weitersuchen ...
Jana66 hat geschrieben: Welcher WLAN-Router?
Fritz!Box 7330 mit Fritz!Os 06.53
Da hatte doch erst einer Probleme nach Firmware-Update:
viewtopic.php?f=30&t=164930
Aber andersrum, Gast ging nicht. Thread ungelöst, deshalb eventuell anderen Router probieren oder FW-Downgrade?!
Umlaute oder Sonderzeichen im WPA2-Passwort? Underline geht.

Mein

Code: Alles auswählen

dpkg -l |grep firmware*
ii  firmware-atheros                                            0.43                                 all          Binary firmware for Atheros wireless cards
ii  intel-microcode                                             3.20161104.1~deb8u1                  amd64        Processor microcode firmware for Intel CPUs
Du hast irgendwie jeden Treiber installiert ...

Nu haste zu tun ... :hail:
LG Jana

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 25.04.2017 09:37:50

hallo Jana66
Hab den Lappi gestern Abend mal ne Zeitlang laufen lassen und Internet Radio gehört. Es gab immer wieder Abbrüche in der Verbindung. Allerdings wurde die Verbindung dann [meist] wieder automatisch aufgebaut. Lass es grad mal laufen und mit protokollieren ---> Bisher keinen Ausfall
Habe gestern noch was gemacht, was ich nicht erwähnt habe :facepalm:
von der Seite https://digitz.org/blog/wifi-issue-on-a ... vice-0042/
Hab ich folgendes ausgeführt, ohne alerdings genau zu wissen, was ich da so tue:
Aus dem Workaround:
# Modify the config files:

Code: Alles auswählen

echo "options ath10k_core skip_otp=y" | sudo tee /etc/modprobe.d/ath10k_core.conf
Die nachfolgenden Schritte:

Code: Alles auswählen

#Download the backport
wget https://www.kernel.org/pub/linux/kernel/projects/backports/2015/11/20/backports-20151120.tar.gz
# Extract it
tar zxvf backports-20151120.tar.gz
# cd to the directory, compile and install it. The commands 'make' and 'make install' will take some time to finish
cd backports-20151120
make defconfig-wifi
make
sudo make install
Hab ich nicht ausgeführt, da die Kernel Treiber nun schon 2 Jahre alt sind, und pausenlos Fehlermeldungen beim kompilieren kamen weil noch dies und das an libs fehlte
weiter ging es mit

Code: Alles auswählen

# Download the firmware for the WiFi card
git clone https://github.com/kvalo/ath10k-firmware.git

# Copy the firmware to appropriate locations. 
sudo cp -r ath10k-firmware/QCA9377 /lib/firmware/ath10k/
sudo cp /lib/firmware/ath10k/QCA9377/hw1.0/firmware-5.bin_WLAN.TF.1.0-00267-1 /lib/firmware/ath10k/QCA9377/hw1.0/firmware-5.bin
Das Verzeichniss sieht jetzt so aus:
hans@aspire:/lib/firmware/ath10k/QCA9377/hw1.0$ ls -ltc
insgesamt 1664
-rw-r--r-- 1 root root 605908 Apr 24 17:33 firmware-5.bin
drwxr-xr-x 2 root root 4096 Apr 24 17:32 untested
-rw-r--r-- 1 root root 427668 Apr 24 17:32 board-2.bin
-rw-r--r-- 1 root root 8124 Apr 24 17:32 board.bin
-rw-r--r-- 1 root root 605908 Apr 24 17:32 firmware-5.bin_WLAN.TF.1.0-00267-1
-rw-r--r-- 1 root root 46142 Apr 24 17:32 notice.txt_WLAN.TF.1.0-00267-1
Das alte sah so aus:
/lib/firmware/ath10k/QCA9377/hw1.0# ls -ltc
insgesamt 1020
-rw-r--r-- 1 root root 427668 Dez 24 09:56 board-2.bin
-rw-r--r-- 1 root root 8124 Dez 24 09:56 board.bin
-rw-r--r-- 1 root root 605908 Dez 24 09:56 firmware-5.bin
Das erklärt auch die Zeilen von hier:viewtopic.php?f=30&t=164985#p1129977

Code: Alles auswählen

[    4.270291] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/firmware-5.bin
[    4.270304] ath10k_pci 0000:03:00.0: qca9377 hw1.1 target 0x05020001 chip_id 0x003821ff sub 11ad:08a6
[    4.270308] ath10k_pci 0000:03:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[    4.271506] ath10k_pci 0000:03:00.0: firmware ver WLAN.TF.1.0-00267-1 api 5 features ignore-otp crc32 79cea2c7
[    4.339334] ath10k_pci 0000:03:00.0: firmware: direct-loading firmware ath10k/QCA9377/hw1.0/board-2.bin
[    4.339805] ath10k_pci 0000:03:00.0: board_file api 2 bmi_id N/A crc32 93da0176
[    6.165124] ath10k_pci 0000:03:00.0: htt-ver 3.1 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
Jana66 hat geschrieben: Jana66 hat geschrieben: Welcher WLAN-Router?
Fritz!Box 7330 mit Fritz!Os 06.53
Da hatte doch erst einer Probleme nach Firmware-Update:
viewtopic.php?f=30&t=164930
Aber andersrum, Gast ging nicht. Thread ungelöst, deshalb eventuell anderen Router probieren oder FW-Downgrade?!
Umlaute oder Sonderzeichen im WPA2-Passwort? Underline geht.
Nee - das Problem war, dass ich gestern, im Zuge der Fehlersuche natürlich auch den Router überprüft habe, und mir ein Update angeboten wurde.
Das Update ist hängen geblieben und ich hab versehentlich ne alte config-Datei zurück gesichert. Dabei wurde die MAC Adresse meines neuen Lappis "unterschlagen :facepalm: :facepalm:
Erst danach hab ich das Update aber mit der iso, die ich dann vorher runter geladen habe durchgeführt und die MAC-Adresse wieder zugefügt.

Mein

Code: Alles auswählen

dpkg -l |grep firmware*
ii  firmware-atheros                                            0.43                                 all          Binary firmware for Atheros wireless cards
ii  intel-microcode                                             3.20161104.1~deb8u1                  amd64        Processor microcode firmware for Intel CPUs
Du hast irgendwie jeden Treiber installiert ...

Nu haste zu tun ... :hail:
LG Jana[/quote]

Das mit den Treibern liegt an SparkyLinux die hauen gleich alles in das Installations-ISO, da bin ich (fast) unschuldig :roll:

Aber da gibt es noch einiges zu bereinigen - an anderer Stelle - in einem neuen Thread.

Was Bleibt, sind die Unterbrechungen. In der Zeit, in der ich das schreibe ist es doch inzwischen drei Mal passiert.

iw event -r -f rund um den Abbruch und manuellem Neuverbinden:

Code: Alles auswählen

6.646436: wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825, ""
8.080998: wlan0 (phy #0): CQM event: peer 9c:c7:a6:57:f9:52 didn't ACK 50 packets
20.242112: wlan0 (phy #0): CQM event: peer 9c:c7:a6:57:f9:52 didn't ACK 50 packets
19.210238: wlan0 (phy #0): CQM event: peer 9c:c7:a6:57:f9:52 didn't ACK 50 packets
19.986201: wlan0 (phy #0): CQM event: peer 9c:c7:a6:57:f9:52 didn't ACK 50 packets
5.462623: wlan0: del station 9c:c7:a6:57:f9:52
0.006002: wlan0 (phy #0): deauth 94:e9:79:ab:0a:fd -> 9c:c7:a6:57:f9:52 reason 3: Deauthenticated because sending station is leaving (or has left) the IBSS or ESS [frame: c0 00 00 00 9c c7 a6 57 f9 52 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 00 00 03 00]
0.000028: wlan0 (phy #0): disconnected (local request)
0.007641: phy #0: regulatory domain change: set to world roaming by the wireless core upon initialization request
0.113822: wlan0 (phy #0): scan started
0.635291: phy #0: beacon hint:
phy0 5180 MHz [36]:
	o Initiating radiation enabled
1.503557: wlan0 (phy #0): scan aborted: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825, ""
0.186036: wlan0: new station 9c:c7:a6:57:f9:52
0.004277: wlan0 (phy #0): auth 9c:c7:a6:57:f9:52 -> 94:e9:79:ab:0a:fd status: 0: Successful [frame: b0 00 3a 01 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 9c c7 a6 57 f9 52 00 10 00 00 02 00 00 00]
0.010643: wlan0 (phy #0): assoc 9c:c7:a6:57:f9:52 -> 94:e9:79:ab:0a:fd status: 0: Successful [frame: 10 00 3a 01 94 e9 79 ab 0a fd 9c c7 a6 57 f9 52 9c c7 a6 57 f9 52 20 10 31 04 00 00 02 c0 01 08 82 84 8b 0c 12 96 18 24 32 04 30 48 60 6c 2d 1a ee 11 1b ff ff 00 00 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 33 1a ee 11 1b ff ff 00 00 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 3d 16 01 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 34 16 01 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4a 0e 14 00 0a 00 2c 01 c8 00 14 00 05 00 19 00 7f 05 01 00 00 00 00 dd 18 00 50 f2 02 01 01 02 00 03 a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00]
0.000067: wlan0 (phy #0): connected to 9c:c7:a6:57:f9:52
0.003956: phy #0: regulatory domain change: set to DE by a country IE request on phy0
0.897179: wlan0 (phy #0): scan started
6.414216: wlan0 (phy #0): scan finished: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825, ""
36.586833: wlan0 (phy #0): scan started
^C
Jana66 hat geschrieben: Ich empfehle dir das Programm linssid für Kanalplanung/Übersicht. Ist nicht in Paketquellen.
Des Weiteren könntest du später, wenn alles läuft, am Router 802.11n für 2,4 GHz einstellen sowie aufgrund der vielen WLANs auf 5 GHz 802.11n oder ac umsteigen bzw. zusätzlich nutzen. 5 GHz hat eine viel geringere Reichweite aufgrund höherer Dämpfung.
Das scheinen mir im Augenblick die entscheidenden Ratschläge zu sein, die ich mal heute Abend ausprobieren werde.
LinSSID hab ich mir mal runter geladen :THX:

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 25.04.2017 13:56:04

geier22 hat geschrieben:Das scheinen mir im Augenblick die entscheidenden Ratschläge zu sein ...
Das glaube ich nicht so ganz, die waren für später gedacht. :wink:
Du hast einen neuen Lappi, eine neue Installation, einen Router, wo man sich derzeit nicht ganz sicher sein kann.
Ich würde erst Fehler eingrenzen mit Schnelltests: Ubuntu/Mint-Live-Iso. Router funktioniert ohne Aussetzer? dmesg/journalctl vom Ubuntu/Mint?
LinSSID hab ich mir mal runter geladen
Gerade entdeckt: Debianlinssid ist nun auch in Debian-Paketquellen. Aber du nutz ja Sparky.
Das mit den Treibern liegt an SparkyLinux die hauen gleich alles in das Installations-ISO, da bin ich (fast) unschuldig :roll:
Im 1. Beitrag war es Stretch/XFCE?! Anderer WLAN-Client wäre natuerlich sinnvoll, um Routerfehler auszuschließen.
...hab mir einen Acer Aspire E 15 - E5-575G-56WG zugelegt, Stretch XFCE installiert...
Debianlinssid beruht jedenfalls auf und wird dir nicht mehr verraten - ausser besserer Überblick und Schwankungen. :wink:

Denk dran: Bei 2,4 GHz 4 oder 5 Kanäle Abstand zum Nachbarn, wenn nicht möglich, direkt auf einen Nachbarn, der nicht von Dritten ueberschnitten wird, bei 5 GHz evtl DFS/Radarerkennung, 60 sec Wartezeit und automatische Kanalwechsel mit Disconnects möglich.
https://avm.de/service/fritzbox/fritzbo ... t-nutzbar/
https://ffmuc.net/wiki/p/5GHz
https://www.lancom-systems.de/docs/LCOS ... s/dfs.html
https://www.heise.de/ct/artikel/Technis ... 97988.html
Zum Testen Kanäle 36 bis 48. (Wegen hoher Daempfung stören andere eh nicht so wie mit 2,4 GHz.)
Kanalbreite vorerst nur HT20 oder 40 und 802.11n mit fest eingestellten Kanal.
Aber wie gesagt, die Basteleien würde ich erst nach o. g. Test tun ...

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 25.04.2017 14:47:41

so jetzt hab ich mal auf einen anderen Kanal (kanal 13 /2,472 GHz) uneingestellt, mit dem Erfolg, dass das dem Smartphone das zwar egal ist, aber der Laptop mein Funknetz nicht mehr findet
auch nicht mit iwlist scan :oops: :oops: :oops:
Hier mal die Grafik von der Fritz!Box
Bild Bild
Jana66 hat geschrieben:Gerade entdeckt: Debianlinssid ist nun auch in Debian-Paketquellen. Aber du nutz ja Sparky.
Was stellt ihr euch denn unter Sparky schlimmes vor ? :roll:
Sparky benutzt die original Repos von Debian und habt noch ein eigenes Repo mit diversen Tools und Grimmicks.Und Debianlinssid ist deshalb natürlich auch vorhanden. :mrgreen:
Das ist alles. Allerdings hab ich mit dem Installer noch nie Probleme gehabt - im Gegensatz zu Debian. Das ist der Hauptgrund, warum ich es immer wieder nutze.
5 GHz gibt es leider bei meinem Router nicht (ist halt etwas betagt :roll:
Hab mir mal Mint 18.1 runter geladen und werde das nachher mal probieren

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 25.04.2017 15:02:01

geier22 hat geschrieben:so jetzt hab ich mal auf einen anderen Kanal (kanal 13 /2,472 GHz) uneingestellt,
Und das mit 40 MHz Kanalbreite. Jetzt ist das halbe Band vollgeballert - trotz Nachbarn. :evil:
Nimm linssid (sieht man besser) und stelle auf Fritte 20 MHz Kanalbreite 802.11g+n ein. Kanal 12 und 13 könnten fehlen, wenn der Ländercode auf USA steht. Linssid würde dann 1 - 11 anzeigen, dein WLAN-Kaete könnte/dürfte u. U. nur so. Ohne "Worldmodus".
Was stellt ihr euch denn unter Sparky schlimmes vor ? :roll:
Ich dachte, das sei ein Windows-Derivat von und für Menschenfresser. :mrgreen: Quatsch, habe mich nur über den Wechsel gewundert.

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 25.04.2017 16:08:02

So hab mal Mint 18.1 auf ne DVD gepackt. Läuft seit 30 Minuten stabil trotz 1,5 Gb Download und gleichzeitigem Inet-Radio :mrgreen:
Die Fritzbox macht sich ja auf allen Kanälen breit
Bild
Jana66 hat geschrieben:und stelle auf Fritte 20 MHz Kanalbreite 802.11g+n ein.
Wie soll ich das machen? So eine Auswahlmöglichkeit hab ich noch nicht gefunden.

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 25.04.2017 16:21:01

geier22 hat geschrieben:Wie soll ich das machen? So eine Auswahlmöglichkeit hab ich noch nicht gefunden.
Handbuch Seite 91-93. https://www.google.de/url?sa=t&source=w ... aOw3MCPdIQ
:wink:

Und die linssid-Bildchen sind besser als die der FB: (Nachbar-) Pegel, SNR, Authentifizierung etc. Damit wuerde ich Kanal und -breite festlegen. In eine Live-Iso kann man auch (temporär) nachinstallieren.
So hab mal Mint 18.1 auf ne DVD gepackt. Läuft seit 30 Minuten stabil trotz 1,5 Gb Download und gleichzeitigem Inet-Radio :mrgreen:
Was sagt dmesg/journalctl? Wenn gut, weisst du, wo du Fehler suchen musst: Router/WLAN funktioniert, neuem Lappis HW funktioniert, Mint funktioniert ...

geier22

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von geier22 » 26.04.2017 09:51:39

So nach einer langen Nacht bin ich letztendlich bei Siduction Xfce gelandet :mrgreen: :THX: Bild
Grund: Mint läuft zwar, aber ich will doch bei Debian bleiben. Der Installer bei Mint ist schlichtweg Schrott, wenn man was anderes will, als vorgegeben, bricht er ab. Ausserdem hatte er schwierigkeien mit meiner M.2 SSD, und wollte darauf ums Verrecken nicht Grub installieren. Witzig ist allerdings, das kein Installer außer dem von Sparky es schafft, das /home auf einer anderen Platte zu installieren finde ich mehr als ernüchternd. Siduction hing sich dabei bei einem Job fillkchome(oder so ähnlich) auf und legte einen "siducer" auf der zweiten Platte an.
Hat schon seinen Grund, warum ich Sparky benutze.
So, nach der Meckerei die Hausaufgaben :wink:
dmesg |grep ath10k -----> NoPaste-Eintrag39818

So richtig rund läuft das nicht :oops:

Code: Alles auswählen

root@aspire:/home/hans# dmesg |grep fail
[    0.539293] platform MSFT0101:00: failed to claim resource 1
[    0.539303] acpi MSFT0101:00: platform device creation failed: -16
[    5.378946] acer_wmi: Enabling Launch Manager failed: 0xe4 - 0x0
[    5.565301] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/pre-cal-pci-0000:03:00.0.bin (-2)
[    5.565302] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:03:00.0.bin failed with error -2
[    5.565525] ath10k_pci 0000:03:00.0: firmware: failed to load ath10k/cal-pci-0000:03:00.0.bin (-2)
[    5.565526] ath10k_pci 0000:03:00.0: Direct firmware load for ath10k/cal-pci-0000:03:00.0.bin failed with error -2
[ 3389.334477] ath10k_pci 0000:03:00.0: failed to install key for vdev 0 peer 9c:c7:a6:57:f9:52: -110
[ 3389.334484] wlp3s0: failed to remove key (0, 9c:c7:a6:57:f9:52) from hardware (-110)
root@aspire:/home/hans# 
Bild
Jana66 hat geschrieben:Und die linssid-Bildchen sind besser als die der FB: (Nachbar-) Pegel, SNR, Authentifizierung etc. Damit wuerde ich Kanal und -breite festlegen. In eine Live-Iso kann man auch (temporär) nachinstallieren.
Das funktioniert nicht bei der Fritzbox. Egal, welchen Kanal ich wähle es sind immer 40 MHZ
hier mal noch der Screen von linssid:
Bild

mat6937
Beiträge: 2925
Registriert: 09.12.2014 10:44:00

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von mat6937 » 26.04.2017 10:02:36

geier22 hat geschrieben:
Jana66 hat geschrieben:Und die linssid-Bildchen sind besser als die der FB: (Nachbar-) Pegel, SNR, Authentifizierung etc. Damit wuerde ich Kanal und -breite festlegen. In eine Live-Iso kann man auch (temporär) nachinstallieren.
Das funktioniert nicht bei der Fritzbox. Egal, welchen Kanal ich wähle es sind immer 40 MHZ
BTW: Die "20 MHz Kanalbreite" kannst Du mit cfg80211 festlegen/konfigurieren. Wie ist die Ausgabe von:

Code: Alles auswählen

lsmod | grep -i ath
?

EDIT:

... und die Ausgabe von:

Code: Alles auswählen

modinfo cfg80211 | grep -i parm
?

BenutzerGa4gooPh

Re: WLAN funktioniert nicht Aspire E 15

Beitrag von BenutzerGa4gooPh » 26.04.2017 11:28:21

geier22 hat geschrieben:hier mal noch der Screen von linssid:
Also so wie momentan sind die ungünstigsten Interferenzen - mit dem starken Netz SSID O2-WLAN51 (ebenfalls 40 MHz Kanalbreite).
Weiche aus auf Kanal 1 oder Kanalwahl Auto! Damit sollte die FB die untere Hälfte des 2,4-GHz-Frequenzbandes nutzen. Fremd-WLANS sind dort schwächer. (Besseres Signal-Rausch-Verhältnis für dich.)
Ob das im Endeffekt die FB richtig macht, solltest du nach Umstellung mit linssid prüfen.

Aufgrund der vielen Nachbar-WLANs wäre ein Dualband-Router und Nutzung des 5-GHz-Frequenzbandes mit DFS/TPC überlegenswert - zumal du nun eine AC-Karte im Lapppi hast. Ein AC1200-Gerät (Fritte mit 2 Streams) sollte völllig reichen. (Auch nur mit 20 MHz Kanalbreite findet man keinen freien Kanal im 2,4-GHz-Band. Eine Umstellung darauf erscheint recht nutzlos.)

Antworten