ich frevler will meinen WG-Server hier auf Eisfair umstellen, und da hab ich folgendes Problem mit meiner Festplatte, das ich bei debian/knoppix nicht habe, wär für mich nur gut zu wissen wie es unter debian funktioniert:
Folgendes Problem:
- Hab ein altes Mainboard, das selbst mit neuestem BIOS nur 32GB kann, musste die Platte also auf 32GB clippen, sonst kann ich garnichts machen. Im BIOS wird sie sonst garnicht erkannt.
- Mit Knoppix ist das ganze kein Problem während des Bootens wird die Platte mir der richtigen Geometrie, und somit mit 80GB erkannt (Hierbei vor allem auf die Zylinderzahl unten achten)
- Hab schon versucht unter Eisfair lilo die Geometrie mitzugeben, was irgendwie nicht klappt (habe lilo.conf mal mit gepastet)
Code: Alles auswählen
root@0[root]# dmesg
[...]
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller at PCI slot 00:07.1
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
hda: SAMSUNG SP0802N, ATA DISK drive
hdb: ASUS CD-S400/A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 156368015 sectors (80060 MB) w/2048KiB Cache, CHS=9733/255/63
Partition check:
hda: hda1 hda2 hda3
ide: late registration of driver.
[...]
root@0[root]# hdparm -i /dev/hda
/dev/hda:
Model=SAMSUNG SP0802N, FwRev=TK100-24, SerialNo=S00JJ30X475421
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=66055248
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: (null):
* signifies the current active mode
root@0[root]# hdparm -g /dev/hda
/dev/hda:
geometry = 9733/255/63, sectors = 156368015, start = 0
root@0[root]#
root@0[root]# cat /etc/lilo.conf
lba32
boot=/dev/hda
install=/boot/boot-menu.b
backup=/dev/null
map=/boot/map
timeout=100
vga=normal
default=Knoppix
image=/vmlinuz
append="lang=de apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 quiet BOOT_IMAGE=knoppix"
root=/dev/hda5
label=Knoppix
read-write
root@0[root]#
Code: Alles auswählen
muehle # hdparm -i /dev/hda
/dev/hda:
Model=SAMSUNG SP0802N, FwRev=TK100-24, SerialNo=S00JJ30X475421
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=66055248
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4 udma5
muehle # hdparm -g /dev/hda
/dev/hda:
geometry = 4111/255/63, sectors = 66055248, start = 0
muehle # cat /var/log/messages
[...]
Dec 13 03:05:15 muehle kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
Dec 13 03:05:15 muehle kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Dec 13 03:05:15 muehle kernel: PIIX3: IDE controller at PCI slot 00:07.1
Dec 13 03:05:15 muehle kernel: PIIX3: chipset revision 0
Dec 13 03:05:15 muehle kernel: PIIX3: not 100%% native mode: will probe irqs later
Dec 13 03:05:15 muehle kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
Dec 13 03:05:15 muehle kernel: hda: SAMSUNG SP0802N, ATA DISK drive
Dec 13 03:05:15 muehle kernel: hdb: ASUS CD-S400/A, ATAPI CD/DVD-ROM drive
Dec 13 03:05:15 muehle kernel: blk: queue c0328f20, I/O limit 4095Mb (mask 0xffffffff)
Dec 13 03:05:15 muehle kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Dec 13 03:05:15 muehle fcron[213]: fcron[213] 2.9.0 started
Dec 13 03:05:15 muehle kernel: hda: attached ide-disk driver.
Dec 13 03:05:15 muehle fcron[213]: updating configuration from /var/spool/fcron
Dec 13 03:05:15 muehle kernel: hda: host protected area => 1
Dec 13 03:05:15 muehle kernel: hda: setmax_ext LBA 156368016, native 66055248
Dec 13 03:05:15 muehle kernel: hda: 66055248 sectors (33820 MB) w/2048KiB Cache, CHS=4111/255/63, (U)DMA
Dec 13 03:05:15 muehle kernel: Partition check:
Dec 13 03:05:15 muehle kernel: hda: hda1 hda2 hda3
Dec 13 03:05:15 muehle kernel: Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Dec 13 03:05:16 muehle kernel: Highpoint HPT370 Softwareraid driver for linux version 0.02
Dec 13 03:05:16 muehle kernel: Guestimating sector 66026894 for superblock
Dec 13 03:05:16 muehle kernel: driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
Dec 13 03:05:16 muehle kernel: md: linear personality registered as nr 1
Dec 13 03:05:16 muehle kernel: md: raid0 personality registered as nr 2
Dec 13 03:05:16 muehle mini_httpd[224]: socket :: - Address family not supported by protocol
Dec 13 03:05:16 muehle kernel: md: raid1 personality registered as nr 3
Dec 13 03:05:16 muehle kernel: md: raid5 personality registered as nr 4
Dec 13 03:05:16 muehle kernel: raid5: measuring checksumming speed
Dec 13 03:05:16 muehle kernel: 8regs : 162.800 MB/sec
Dec 13 03:05:16 muehle kernel: 32regs : 170.400 MB/sec
Dec 13 03:05:16 muehle mini_httpd[225]: started as root without requesting chroot(), warning only
Dec 13 03:05:16 muehle kernel: raid5: using function: 32regs (170.400 MB/sec)
Dec 13 03:05:16 muehle mini_httpd[225]: mini_httpd/1.19 19dec2003 starting on muehle, port 81
Dec 13 03:05:16 muehle kernel: md: multipath personality registered as nr 7
Dec 13 03:05:16 muehle kernel: md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Dec 13 03:05:16 muehle kernel: md: Autodetecting RAID arrays.
Dec 13 03:05:16 muehle kernel: md: autorun ...
Dec 13 03:05:16 muehle kernel: md: ... autorun DONE.
[...]
muehle # cat /etc/lilo.conf
lba32
append="id0=dma hda=scsi"
disk = /dev/hda
bios = 0x80
#inaccessible
#fix-table
cylinders=9733
sectors=63
heads=255
#linear
boot = /dev/hda
read-only
prompt
timeout = 50
vga = normal
image = /boot/kernel
root = /dev/hda1
label = muehle
initrd = /boot/initrd.gz
muehle #
weiss echt nicht weiter,
danke soweit schonmal
gruss
lennart