xawtv... scantv ... was ist falsch?

[ferida]

kann mir einer verraten, was die folgenden meldungen ungefaehr bedeuten sollen:

Code: Alles auswählen

i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.83 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is Advanced Micro Devices [AMD] AMD-751 [Irongate] System Controller
bttv: Bt8xx card found (0).
PCI: Found IRQ 11 for device 00:0d.0
PCI: Sharing IRQ 11 with 00:0d.1
PCI: Sharing IRQ 11 with 00:11.0
bttv0: Bt878 (rev 2) at 00:0d.0, irq: 11, latency: 96, memory: 0xefdfd000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: BT878(Hauppauge (bt848)) [card=2,insmod option]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: Hauppauge eeprom: model=61344, tuner=Philips FM1216 (5), radio=yes
bttv0: i2c: checking for MSP34xx @ 0x80... found
i2c-core.o: driver i2c msp3400 driver registered.
msp34xx: init: chip=MSP3415D-B3, has NICAM support
msp3410: daemon started
bttv0: i2c attach [client=MSP3415D-B3,ok]
i2c-core.o: client [MSP3415D-B3] registered to adapter [bt848 #0](pos. 0).
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951)
i2c-core.o: driver generic i2c audio driver registered.
i2c-core.o: driver i2c TV tuner driver registered.
tuner: chip found @ 0xc2
bttv0: i2c attach [client=Philips PAL,ok]
i2c-core.o: client [Philips PAL] registered to adapter [bt848 #0](pos. 1).
eth1: Setting half-duplex based on auto-negotiated partner ability 0000.
tuner: TV freq (0.-6) out of range (44-958)
tuner: TV freq (0.00) out of range (44-958)
tuner: TV freq (0.00) out of range (44-958)
tuner: TV freq (0.00) out of range (44-958)
bttv0: unloading
bttv0: i2c detach [client=MSP3415D-B3,ok]
i2c-core.o: client [MSP3415D-B3] unregistered.
bttv0: i2c detach [client=Philips PAL,ok]
i2c-core.o: client [Philips PAL] unregistered.
i2c-core.o: adapter unregistered: bt848 #0
bttv: driver version 0.7.83 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Host bridge is Advanced Micro Devices [AMD] AMD-751 [Irongate] System Controller
bttv: Bt8xx card found (0).
PCI: Found IRQ 11 for device 00:0d.0
PCI: Sharing IRQ 11 with 00:0d.1
PCI: Sharing IRQ 11 with 00:11.0
bttv0: Bt878 (rev 2) at 00:0d.0, irq: 11, latency: 96, memory: 0xefdfd000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: BT878(Hauppauge (bt848)) [card=2,insmod option]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
msp34xx: init: chip=MSP3415D-B3, has NICAM support
msp3410: daemon started
bttv0: i2c attach [client=MSP3415D-B3,ok]
i2c-core.o: client [MSP3415D-B3] registered to adapter [bt848 #0](pos. 0).
tuner: chip found @ 0xc2
bttv0: i2c attach [client=(unset),ok]
i2c-core.o: client [(unset)] registered to adapter [bt848 #0](pos. 1).
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: Hauppauge eeprom: model=61344, tuner=Philips FM1216 (5), radio=yes
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tuner: TV freq (0.-6) out of range (44-958)
tuner: TV freq (0.00) out of range (44-958)

das zeigt mir dmesg.

[xraver]

Was geht denn nicht?
Kleine Fehlerbeschreibung (falls ein Fehler vorliegt) wäre interessant.

Was das im allegmeinen Bedeutet? Ich denke mal die initalisierung deiner Karte vom Kernel in einer Menschenlesbaren Form.

[k-pl]

Schon recht lang die Ausgabe. Bei mir sah das immer ein bisserl kürzer aus. Leider habe ich meine Karte nicht mehr, sonst hätte ich mal vergleichen können.

k-pl

[ferida]

also mittlerweile ist es so weit, dass alle modules richtig geladen werden wenn ich xawtv starte (glaub ich zumindest), scantv findet keinen einzigen channel (ja, die karte ist angesteckt) und ausserdem krieg ich diese meldungen beim starten von xawtv:
This is xawtv-3.71, running on Linux/i686 (2.4.17)
WARNING: Your X-Server has no DGA support.
WARNING: couldn't find framebuffer base address, try manual
configuration ("v4l-conf -a <addr>")
ioctl: VIDIOCCAPTURE(on): Invalid argument

das mit dem invalid argument krieg ich dann auch jedes mal wenn ich den channel wechseln will wenn ich die standardeinstellung bei capture (overlay) beibehalte ...

ich muss mal das kabel ueberpruefen aber ganz am anfang als ich das erste mal scantv aufgerufen hab, hat er sogar was gefunden...
keine ahnung was ich da anders gemacht hab?!!